In the past, there were problems such as unstable paper feeding, large registration errors, difficulty in adjusting the machine, ink and flowers, dust, and so on, which have now been greatly improved.
1. Paper-feeding: The traditional paper-feeding unit is a push-back type. It is often not able to feed paper due to the bending of the paperboard, and the paper-feeding cannot guarantee the positioning of the paperboard and generate registration errors. The improved vacuum adsorption for the small area of ​​the adsorption plate or roller assisted, although it can improve the above shortcomings, but for large areas of cardboard due to insufficient contact area will still cause deviation. The large-area adsorption-contact vacuum suction belt-type feeding system developed by the French company Martin can completely solve these problems and ensure the registration precision of the leading edge feed.
2. Paper powder removal device: Now the models with higher printing quality requirements are all equipped with high-voltage discharge dust removal device, which first removes static electricity and then vacuums the dust. This solves the defect that in the past, dust was electrostatically charged and it was difficult to remove on cardboard. , improve the dust removal effect.
3. Cardboard conveying device: The traditional printing machine runs the drawing paper ring in the printing unit. The pulling paper ring needs to adjust the position according to the width of the paper board, and the printing part must be avoided to avoid printing ink. In addition, the staged transfer action will affect the registration accuracy due to the different degree of cardboard bending. The vacuum absorption transfer system developed by Bobst Company uses vacuum adsorption and roller to transport the paperboard. It can suck the paperboard into the machine and transfer it stably between the printing units. There is no periodic beating between the units, which greatly improves the printing. Overprint accuracy, and there is no need to adjust the draw ring position for changing orders.
4. Printing Ink Supply System: In order to adapt to different printing needs different ink amount and network line density, the flexibility of printing unit is very important. Some manufacturers consider the printing unit to be equipped with a rubber ink roller and a closed groove scraper to accommodate full plates and overprints. The French company Martin's rapid replacement of closed trough scraper system can adapt to full version and dot printing with different scrapers. Swiss Bobst company replaces the ceramic anilox roller by electric means and distributes it in each printing unit. Two to three sets of anilox rollers can be replaced within one minute to adapt to a wider range of printing, full-print version and up to 120 lines/inch overprint.
5. Drying unit: In order to adapt to the increasing trend of carton printing, more and more four-color printing units are now equipped with ink. Under this premise, drying equipment is a must. One can improve the printing quality, and the other can increase the production speed. In addition, during the process of connection, the drying unit can isolate the post-printing processing (grooving die-cutting) process so as to prevent dust from entering the printing unit and the vibrations affecting the print quality. The number and configuration of drying units depends on the needs and budget. Bobst's models are designed for multi-color printing and in-line lighting, so hot air drying is pre-configured after each printing unit, and the last unit is equipped with an off-board drying unit to coat the outer varnish.
1. Paper-feeding: The traditional paper-feeding unit is a push-back type. It is often not able to feed paper due to the bending of the paperboard, and the paper-feeding cannot guarantee the positioning of the paperboard and generate registration errors. The improved vacuum adsorption for the small area of ​​the adsorption plate or roller assisted, although it can improve the above shortcomings, but for large areas of cardboard due to insufficient contact area will still cause deviation. The large-area adsorption-contact vacuum suction belt-type feeding system developed by the French company Martin can completely solve these problems and ensure the registration precision of the leading edge feed.
2. Paper powder removal device: Now the models with higher printing quality requirements are all equipped with high-voltage discharge dust removal device, which first removes static electricity and then vacuums the dust. This solves the defect that in the past, dust was electrostatically charged and it was difficult to remove on cardboard. , improve the dust removal effect.
3. Cardboard conveying device: The traditional printing machine runs the drawing paper ring in the printing unit. The pulling paper ring needs to adjust the position according to the width of the paper board, and the printing part must be avoided to avoid printing ink. In addition, the staged transfer action will affect the registration accuracy due to the different degree of cardboard bending. The vacuum absorption transfer system developed by Bobst Company uses vacuum adsorption and roller to transport the paperboard. It can suck the paperboard into the machine and transfer it stably between the printing units. There is no periodic beating between the units, which greatly improves the printing. Overprint accuracy, and there is no need to adjust the draw ring position for changing orders.
4. Printing Ink Supply System: In order to adapt to different printing needs different ink amount and network line density, the flexibility of printing unit is very important. Some manufacturers consider the printing unit to be equipped with a rubber ink roller and a closed groove scraper to accommodate full plates and overprints. The French company Martin's rapid replacement of closed trough scraper system can adapt to full version and dot printing with different scrapers. Swiss Bobst company replaces the ceramic anilox roller by electric means and distributes it in each printing unit. Two to three sets of anilox rollers can be replaced within one minute to adapt to a wider range of printing, full-print version and up to 120 lines/inch overprint.
5. Drying unit: In order to adapt to the increasing trend of carton printing, more and more four-color printing units are now equipped with ink. Under this premise, drying equipment is a must. One can improve the printing quality, and the other can increase the production speed. In addition, during the process of connection, the drying unit can isolate the post-printing processing (grooving die-cutting) process so as to prevent dust from entering the printing unit and the vibrations affecting the print quality. The number and configuration of drying units depends on the needs and budget. Bobst's models are designed for multi-color printing and in-line lighting, so hot air drying is pre-configured after each printing unit, and the last unit is equipped with an off-board drying unit to coat the outer varnish.
Create a cleaner, tidier living room it's very important for your living. Shoe cabinets keep footwear neat, tidy and out of sight. Fold-down cabinet doors open to reveal organized shoe racks and close to create a polished appearance.Save time to search for shoes by organizing your collection in one dedicated storage space. The easy track shoe tower keeps up to 15 pairs of shoes and boots in order, up off the floor, and stored neatly in one place so they`re easy to find and put away. The tower is easy to assemble and can be set on the floor or hung on a heavy-duty steel rail to keep floor space open underneath for additional storage.
Shoes Cabinet,Shoe Cupboard,Shoe Rack Cabinet,Shoe Display Case
Baklam , https://www.baklamjm.com